Wifi Manager

Stagenow - 2.3

Overview

Wi-Fi Manager (Wi-Fi) administers the wireless LAN settings and network profiles for a device, including the settings required for connecting to networks. The Wi-Fi CSP also controls OmniTrail, a set of services available in some Zebra devices that enable highly accurate, secure and power-efficient device locationing. OmniTrail can locate a device to within about 5 feet (1.5 meters). See below for OmniTrail requirements.

OmniTrail Requirements

  • OmniTrail is supported only on the following devices:
    • MC18
    • MC40
    • TC51
    • TC56
    • TC70x
    • TC75x
  • Device must be running Android 5.0 Lollipop or later
  • Device must contain MX 6.3 or higher

Main Functionality

  • Enable/Disable:
    • 802.11ac protocol on the device
    • 802.11n protocol on the device
    • All Wi-Fi communication on the device
    • An existing Wi-Fi network
    • Advanced Logging
    • AggregatedFT
    • Auto RF Band selection
    • Cisco Centralized Key Management (CCKM)
    • Coverage Hole Detection
    • Fast Transition (FT)
    • Fast Transition Resource Request (FTRIC)
    • FIPS Compliance
    • FTOverTheDS
    • Fusion Advanced Logging
    • Hotspot mode (ET50, ET55 with Lollipop only)
    • Hyper Fast Secure Roam (HF SR)
    • Management Frame Protection Mode (802.?11w)
    • OKC (Opportunistic Key Caching)
    • OmniTrail Device-Location Services and Options
    • Password Protect Encryption
    • PMKID Caching
    • PreAuth
    • Radio Resource Measurement (802.?11K)
    • Restricted WLAN Settings UI
    • ScanAssist
    • Setting the Clock from an Access Point (AP)
    • Sub-Net Roam
    • WANCountry
  • Set Hotspot (ET50, ET55 with Lollipop only):
    • AP Channel, Band, SSID and Options
    • Security Modes, Passphrase and Passphrase Encryption
  • Set Wi-Fi to Sleep: Never, Always or Always When Plugged In
  • Use/Do Not Use Network Notifications
  • Select Country automatically or manually
  • Set the RF Band
  • Set Power Savings Mode to: Always Active, WMM-PS, Null Data or PS-POLL
  • Set the band preference
  • Connect to/Disconnect from a Wi-Fi network
  • Disable all existing Wi-Fi networks
  • Remove all existing Wi-Fi networks
  • Encrypt Passwords in transit
  • Encrypt Passwords stored on the device

Target OS

Used to specify the operating system of the target device.

Parm Name: TargetOS

Option Name Description Device Group Requires
2 Android Specifies Android as the operating system of the target device. All

MX: 4.2+

Wi-Fi Enable/Disable

This is the On-Off switch for the Wi-Fi radio. Note: Wi-Fi must be enabled to change certain other Wi-Fi settings, including those controlled by the Network Actions parameter described later in this document. Attempting to change such settings while the Wi-Fi radio is disabled will return an error in the Result XML. Zebra recommends beginning any profile created to change Wi-Fi settings with a command to Enable the Wi-Fi radio.

Caution: Some Wi-Fi parameters vary from conventions used by other CSPs:

  • The "Enable" and "Disable" settings in the Wi-Fi CSP control whether a user or administrator can "turn on" and "turn off" a feature or capability, or to set its state as "active" or "inactive." Such terms in other CSPs refer to the feature's "Usage" setting, which can prevent access to the feature entirely.
  • The value "0" is used in Wi-Fi parameters to "Disable" a feature, select its default setting or "make no change" or "do nothing" to a setting. In most other CSPs, the "0" value is used to select the "make no change" option.

Parm Name: WiFiAction

Option Name Description Device Group Requires
0 Do not change This value (or the absence of this parm from the XML) causes no change to Wi-Fi settings; any previously selected setting will be retained. All

MX: 4.2+

1 Enable Turns the Wi-Fi radio On. All

MX: 4.2+

2 Disable Turns the Wi-Fi radio Off. All

MX: 4.2+

Wi-Fi Sleep Policy

Specifies the state of the Wi-Fi radio when the device enters sleep mode. When Wi-Fi remains enabled during sleep, existing Wi-Fi connections will be maintained as during normal operations. While preferrable for some situations, this mode can significantly reduce battery life.

Android devices by default enter sleep mode after being idle for a specified period of time. While in this mode, apps run in a lower-power state.

Parm Name: WifiSleepPolicy

Option Name Description Device Group Requires
4 Do not change This (null) value (or the absence of this parm from the XML) causes no change to the current sleep policy on the device; any previously selected setting will be retained. All

MX: 4.2+

0 AlwaysOn Causes the Wi-Fi radio to remain enabled when the device goes to sleep, providing running apps with uninterrupted access to Wi-Fi. All

MX: 4.2+

1 PluggedIn Causes the Wi-Fi radio to remain enabled whenever the device is plugged in and not running on battery power regardless of sleep state, providing running apps with uninterrupted access to Wi-Fi. All

MX: 4.2+

2 NeverOn Causes the Wi-Fi radio to be disabled when the device enters sleep mode, dropping any existing Wi-Fi connections. All

MX: 4.2+

Country Selection Auto/Manual

Permits the country-selection preference for network usage and Wi-Fi regulatory setting by the device to be specified. Check the box to select the country manually from the drop-down menu; leave the box unchecked to allow the network router or Wi-Fi access point to select the country using the 802.11d protocol.

Parm Name: UseRegulatory

Option Name Description Device Group Requires
11 UseRegulatory Permits manual country selection. All

MX: 4.2+

12 Country Allows the country to be determined by the router. All

MX: 4.2+

Country

Permits selection of country-specific Wi-Fi regulatory settings. Choosing "AUTO" enables 802.11d selection, which configures the device to listen for a country-specific beacon. Using the AUTO setting, the device will not transmit unless it can successfully detect the country and use a frequency that is consistent with the country's Wi-Fi infrastructure. This setting is the least likely to violate country-specific regulations. Countries that do not support the 802.11d infrastructure must be selected manually.

Shown if: The "Configure Country (Auto/Manual)" box is unchecked

Parm Name: Country

Option Name Description Device Group Requires
AUTO AUTO (Use 802.11d) All

MX: 4.2+

DZ Algeria All

MX: 4.2+

AI Anguilla All

MX: 4.2+

AR Argentina All

MX: 4.2+

AU Australia All

MX: 4.2+

AT Austria All

MX: 4.2+

BS Bahamas All

MX: 4.2+

BH Bahrain All

MX: 4.2+

BB Barbados All

MX: 4.2+

BY Belarus All

MX: 4.2+

BE Belgium All

MX: 4.2+

BM Bermuda All

MX: 4.2+

BO Bolivia All

MX: 4.2+

BQ Bonaire All

MX: 4.2+

BA Bosnia and Herzegovina All

MX: 4.2+

BR Brazil All

MX: 4.2+

BG Bulgaria All

MX: 4.2+

CA Canada All

MX: 4.2+

KY Cayman Islands All

MX: 4.2+

CL Chile All

MX: 4.2+

CN China All

MX: 4.2+

CX Christmas Island All

MX: 4.2+

CO Columbia All

MX: 4.2+

CR Costa Rica All

MX: 4.2+

HR Croatia All

MX: 4.2+

CW Curacao All

MX: 4.2+

CY Cyprus All

MX: 4.2+

CZ Czech Republic All

MX: 4.2+

DK Denmark All

MX: 4.2+

DO Dominican Republic All

MX: 4.2+

EC Ecuador All

MX: 4.2+

EG Egypt All

MX: 4.2+

SV El Salvador All

MX: 4.2+

EE Estonia All

MX: 4.2+

FK Falkland Islands(Malvinas) All

MX: 4.2+

FI Finland All

MX: 4.2+

FR France All

MX: 4.2+

GF French Guiana All

MX: 4.2+

DE Germany All

MX: 4.2+

GR Greece All

MX: 4.2+

GP Guadelope All

MX: 4.2+

GU Guam All

MX: 4.2+

GT Guatemala All

MX: 4.2+

GY Guyana All

MX: 4.2+

HT Haiti All

MX: 4.2+

HN Honduras All

MX: 4.2+

HK Hong Kong All

MX: 4.2+

HU Hungary All

MX: 4.2+

IS Iceland All

MX: 4.2+

IN India All

MX: 4.2+

ID Indonesia All

MX: 4.2+

IE Ireland All

MX: 4.2+

IL Israel All

MX: 4.2+

IT Italy All

MX: 4.2+

JM Jamaica All

MX: 4.2+

JP Japan All

MX: 4.2+

JO Jordan All

MX: 4.2+

KZ Kazakhstan All

MX: 4.2+

KE Kenya All

MX: 4.2+

KR Korea Republic All

MX: 4.2+

KW Kuwait All

MX: 4.2+

LV Latvia All

MX: 4.2+

LB Lebanon All

MX: 4.2+

LI Liechtenstein All

MX: 4.2+

LT Lithuania All

MX: 4.2+

LU Luxembourg All

MX: 4.2+

MK Macedonia, Former Yugoslav Republic All

MX: 4.2+

MY Malaysia All

MX: 4.2+

MT Malta All

MX: 4.2+

MQ Martinique All

MX: 4.2+

MX Mexico All

MX: 4.2+

ME Montenegro All

MX: 4.2+

MA Morocco All

MX: 4.2+

AN Netherlands, Antilles All

MX: 4.2+

NL Netherlands All

MX: 4.2+

NZ New Zealand All

MX: 4.2+

NI Nicaragua All

MX: 4.2+

NG Nigeria All

MX: 4.2+

NU Niue All

MX: 4.2+

NF Norfolk Islands All

MX: 4.2+

MP Northern Marina Islands All

MX: 4.2+

NO Norway All

MX: 4.2+

OM Oman All

MX: 4.2+

PK Pakistan All

MX: 4.2+

PA Panama All

MX: 4.2+

PY Paraguay All

MX: 4.2+

PE Peru All

MX: 4.2+

PH Philippines All

MX: 4.2+

PL Poland All

MX: 4.2+

PT Portugal All

MX: 4.2+

PR Puerto Rico All

MX: 4.2+

QA Qatar All

MX: 4.2+

RO Romania All

MX: 4.2+

RU Russian Federation All

MX: 4.2+

SX St. Maarten All

MX: 4.2+

SA Saudi Arabia All

MX: 4.2+

RS Serbia All

MX: 4.2+

SG Singapore All

MX: 4.2+

SK Slovakia All

MX: 4.2+

SI Slovenia All

MX: 4.2+

ZA South Africa All

MX: 4.2+

ES Spain All

MX: 4.2+

LK Sri Lanka All

MX: 4.2+

SE Sweden All

MX: 4.2+

CH Switzerland All

MX: 4.2+

TW Taiwan, Province of China All

MX: 4.2+

TH Thailand All

MX: 4.2+

TT Trinidad and Tobago All

MX: 4.2+

TN Tunisia All

MX: 4.2+

TR Turkey All

MX: 4.2+

UA Ukraine All

MX: 4.2+

AE United Arab Emirates All

MX: 4.2+

GB United Kingdom All

MX: 4.2+

US U.S.A. All

MX: 4.2+

UY Uruguay All

MX: 4.2+

VE Venezuela All

MX: 4.2+

VN Vietnam All

MX: 4.2+

VG Virgin Islands(British) All

MX: 4.2+

VI Virgin Islands(US) All

MX: 4.2+

802.11n

This is the On/Off switch for 802.11n wireless protocol on the device, which operates on the 2.4GHz and 5GHz bands and provides faster transfer rates than 802.11ag.

Note: Disabling 802.11n also disables the 802.11ac protocol on the device.

Parm Name: 802.11n

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the setting; any previously selected setting will be retained. A

MX: 7.0+

1 Enable Enables 802.11n wireless protocol on the device. A

MX: 7.0+

0 Disable Disables 802.11n and 802.11ac wireless protocols on the device. A

MX: 7.0+

802.11ac

This is the On/Off switch for 802.11ac wireless protocol on the device, which operates on the 5GHz band and provides faster transfer rates than 802.11n and other earlier protocols. Requires network infrastructure that explicitly supports the 802.11ac protocol.

Note: Enabling 802.11ac also enables the 802.11n protocol on the device.

Parm Name: 802.11ac

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the setting; any previously selected setting will be retained. A

MX: 7.0+

1 Enable Enables 802.11ac and 802.11n wireless protocols on the device. A

MX: 7.0+

0 Disable Disables 802.11ac wireless protocol on the device. A

MX: 7.0+

802.11v

This is the On/Off switch for 802.11v wireless protocol on the device, which permits connected devices to obtain network load and other information from nearby access points to help make roaming decisions.

Parm Name: 802.11n

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the setting; any previously selected setting will be retained. A

MX: 7.1+

1 Enable Enables 802.11v wireless protocol on the device. A

MX: 7.1+

0 Disable Disables 802.11v wireless protocol on the device. A

MX: 7.1+

RF Band Selection

Used to specify which RF band(s) the device will use for 802.11 communications. This parameter is usually set automatically through negotiation with the Wi-Fi infrastructure. However, it might sometimes be desirable to limit Wi-Fi communications to certain bands, leaving other bands free for other purposes.

Parm Name: BandSelection

Option Name Description Device Group Requires
0 Unchanged This value (or the absence of this parm from the XML) causes no change to the band(s) currently selected on the device; any previously selected setting will be retained. All

MX: 4.2+

1 2.4GHz Selects the 2.4GHz band for Wi-Fi communications. All

MX: 4.2+

2 5.0GHZ Selects the 5.0GHz band for Wi-Fi communications. All

MX: 4.2+

3 Auto Enables 2.4GHz and 5.0GHz bands to operate on the device and allows the connection to selected automatically. All

MX: 4.2+

Network Notification

Controls whether to present user notifications when unknown, open networks such as those offered by public Wi-Fi come into range of the device. If enabled, the user will be presented with the opportunity to connect with such networks. This might be desireable for personal or dual-use devices, but could introduce vulnerabilities when connecting to non-secure or otherwise unknown networks. Zebra recommends disabling Network Notification on devices intended for use only on corporate Wi-Fi networks.

Parm Name: NetworkNotification

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the current network notification setting; any previously selected setting will be retained. All

MX: 4.2+

1 true Enables user notifications to be displayed when unknown, open network(s) come into range. All

MX: 4.2+

0 false Disables user notifications when unknown, open networks come into range. All

MX: 4.2+

Set 2.4GHz Channels

Used to designate channels in the 2.4GHz band for use by the device. While channels used in this band are generally determined automatically through negotiation with the Wi-Fi infrastructure, channels or sets of channels also may be specified manually to avoid interference with other devices or to dedicate certain channels to specific purposes. Warning: Not all channels are available in all countries. See the List of WLAN Channels for more information.

Parm value input rules:

  • String from 0-64 characters containing a set of valid channels
  • Multiple values must be separated by commas (i.e. "1,6,11,14")
  • Also accepts ranges when specified with a hyphen (-) (i.e. "1,7-10")

Shown if: The selected RF Band is "2.4GHz" or "Auto"

Parm Name: 2.4GHzChannels

Requires:

  • MX: 4.2+

Set 5.0GHz Channels

Used to designate channels in the 5GHz band for use by the device. While channels used in this band are generally determined automatically through negotiation with the Wi-Fi infrastructure, channels or sets of channels also can be specified manually to avoid interference with other devices or to dedicate certain channels for specific purposes. Warning: Not all channels are available in all countries. See the List of WLAN Channels for more information.

Parm value input rules:

  • String from 0-64 characters containing a set of valid channels
  • Multiple values must be separated by commas (i.e. "7,11,12,16...")
  • Also accepts ranges when specified with a hyphen (-) (i.e. "36-60")

Shown if: The selected RF Band is "5.0GHz" or "Auto"

Parm Name: 5.0GHzChannels

Requires:

  • MX: 4.2+

Use Diagnostic Options (checkbox)

Controls whether Diagnostic Options will be used on the device. Generally used only at the direction of Zebra support staff; impacts device performance and behavior. Used to collect additional information for troubleshooting. When checked, Fusion Advanced Logging can also be enabled.

Parm Name: UseDiagnosticOptions

Option Name Description Device Group Requires
1 (checked) Allows device diagnostics options to be selected. All

MX: 4.4+

0 (unchecked) Prevents diagnostics options from being displayed for selection. All

MX: 4.4+

Fusion Advanced Logging (checkbox)

Controls whether Fusion Advanced Logging will be used on the device. Available only when Advanced Wi-Fi Options are enabled.

This option is generally used only at the direction of Zebra support staff.

Shown if: The "Use Diagnostic Options" box is checked

Parm Name: FusionAdvancedLogging

Option Name Description Device Group Requires
1 (checked) Enables logging on the device. All

MX: 4.4+

0 (unchecked) Disables logging on the device. All

MX: 4.4+

Network Action

Used to manage the Wi-Fi network profiles on the device, each of which contains the settings necessary to connect to an individual Wi-Fi network. Any number of profiles can be defined and stored on the device using the parameters relevant to "Add a New Network" below. Profiles can be used to control the networks to which a device will be allowed to connect or to force connections to a particular network.

Parm Name: NetworkAction

Option Name Description Device Group Requires
0 Do nothing This value (or the absence of this parm from the XML) will perform no Network Action. All

MX: 4.2+

1 Add This value will add a new profile with the profile settings specified. All

MX: 4.2+

2 Remove Remove an existing network profile based on the SSID specified. All

MX: 4.2+

3 Connect Initiates a connection to an existing network based on the SSID specified. All

MX: 4.2+

4 Disconnect Disconnects from a network based on the SSID specified. All

MX: 4.2+

5 Enable Enables a network profile based on the SSID specified. All

MX: 4.2+

6 Disable Disables a network profile based on the SSID specified. All

MX: 4.2+

7 DisableAll Disables all network profiles on the device. All

MX: 4.2+

8 RemoveAll Deletes all network profiles from the device. All

MX: 4.2+

SSID

This is the SSID name of the network, which is the primary mechanism used to identify a Wi-Fi network and is used to identify the Wi-Fi network profile to be acted on. Therefore, any Network Action that is used to affect a single profile need to specify the SSID to select the desired profile.

Parm value input rules:

  • String with a minimum size of 1 character and a maximum size of 32 characters

Shown if: The Network Action is any option other than "Do Nothing", "Disable All Existing Networks", or "Remove All Existing Networks"

Parm Name: SSID

Requires:

  • MX: 4.2+

Security Mode

This indicates that the network uses 802.1x Extensible Authentication Protocol (EAP) security. These networks use authentication to establish the entitlement of a device to join the network and then distribute necessary keys once this entitlement has been verified. Security information pertaining to the EAP type and authentication credentials to be used will need to be supplied to configure these networks.

Open network security is not generally advisable since no security credentials are needed to connect. If an open network is to be used, security can be added through VPNs, data encryption, or other means.

Basic security generally implements a Pre-Shared Key (PSK) or Wired Equivalent Privacy (WEP) key known to the device and the Wi-Fi infrastructure to encrypt data. These networks are more secure than open networks, but can be compromised if the keys are not handled securely and/or changed periodically. Security information pertaining to the required key must be supplied to configure these networks.

Shown if: The Network Action is "Add a New Network"

Parm Name: SecurityMode

Option Name Description Device Group Requires
0 Open Sets the device to use no security. All

MX: 4.2+

1 Personal Sets the device to use basic security. All

MX: 4.2+

2 Enterprise Sets the device to use advanced security. All

MX: 4.2+

WPA Mode

When the selected Security Mode is "Personal" or "Enterprise," the WPA Mode must be specified to determine the key type to use. WPA performs encryption using the Temporal Key Integrity Protocol. A TKIP-compatible key must be specified. WPA2 supports encryption using TKIP (and is therefore backward-compatibile with WPA) and the more secure Advanced Encryption Standard (AES) algorithm. For key selection for this mode, specify either TKIP, AES or auto-select.

Note: WEP is not supported with Enterprise Security Mode.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal" or "Enterprise"

Parm Name: WPAMode

Option Name Description Device Group Requires
1 WPA Enables Wi-Fi Protected Access (WPA) encryption mode on the device. All

MX: 4.2+

2 WPA2 Enables Wi-Fi Protected Access version 2 (WPA2) standard on the device. All

MX: 4.2+

3 WPA/WPA2 Enables Wi-Fi Protected Access (WPA) standard on the device. All

MX: 4.2+

4 WEP Enables Wired Equivalency Privacy (WEP) standard on the device. All

MX: 4.2+

Authentication

Used to specify the Authentication Mode used by the network. When a Security Mode of "Enterprise" is selected, an Authentication Mode must be specified to determine how authentication will be performed as part of the 802.1x EAP type used by the network.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise"

Parm Name: Authentication

Option Name Description Device Group Requires
1 EAP-TLS This indicates that the network requires authentication using the 802.1x Extensible Authentication Protocol - Transport Layer Security (EAP-TLS) standard (RFC 5216). EAP-TLS requires a device identity to be specified and requires that a client certificate be specified to prove the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

13 EAP-FAST-GTC This indicates that the network requires authentication using a token generated using a Generic Token Card (GTC) within an anonymous TLS tunnel established using the 802.1x Extensible Authentication Protocol - Flexible Authentication via Secure Tunneling (EAP-FAST) standard (RFC 5422). EAP-FAST-GTC requires a device identity to be specified and requires that a token value (typically obtained from a physical token device) be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

11 WPA/WPA2 This indicates that the network requires authentication using the Microsoft Challenge Authentication Protocol Version 2 (MSCHAPV2) within an anonymous TLS tunnel established using the 802.1x Extensible Authentication Protocol - Flexible Authentication via Secure Tunneling (EAP-FAST) standard (RFC 5422). EAP-FAST-MSCHAPV2 requires a device identity to be specified and requires that a password be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

8 EAP-TTLS-PAP This indicates that the network requires authentication using the Password Authentication Protocol (PAP) within a secure TLS tunnel established using the 802.1x Extensible Authentication Protocol - Tunneled Transport Layer Security (EAP-TTLS) standard (RFC 5281). EAP-TTLS-PAP requires a device identity to be specified and requires that a password be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

6 EAP-TTLS-MSCHAP This indicates that the network requires authentication using the Microsoft Challenge Authentication Protocol (MSCHAP) within a secure TLS tunnel established using the 802.1x Extensible Authentication Protocol - Tunneled Transport Layer Security (EAP-TTLS) standard (RFC 5281). EAP-TTLS-MSCHAP requires a device identity to be specified and requires that a password be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

7 EAP-TTLS-MSCHAPV2 This indicates that the network requires authentication using the Microsoft Challenge Authentication Protocol Version 2 (MSCHAPV2) within a secure TLS tunnel established using the 802.1x Extensible Authentication Protocol - Tunneled Transport Layer Security (EAP-TTLS) standard (RFC 5281). EAP-TTLS-MSCHAPV2 requires a device identity to be specified and requires that a password be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

4 LEAP This indicates that the network requires authentication using the Lightweight Extensible Authentication Protocol (LEAP) defined by Cisco. LEAP uses a modified version of MSCHAP without a secure tunnel and hence can be easily compromised. LEAP requires a device identity to be specified and requires that a password be specified to prove the authenticity of that device identity. Unlike standard EAP modes, LEAP does not support an optional certificate to help verify the identity of the authentication server. All

MX: 4.2+

2 PEAP-MSCHAPV2 This indicates that the network requires authentication using the Microsoft Challenge Authentication Protocol Version 2 (MSCHAPV2) within a secure TLS tunnel established using the Protected Extensible Authentication Protocol, (PEAP) defined by Cisco Systems, Microsoft, and RSA Security. PEAP-MSCHAPV2 requires a device identity to be specified and requires that a password be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

10 PEAP-GTC This indicates that the network requires authentication using a token generated using a Generic Token Card (GTC) within a secure TLS tunnel established using the Protected Extensible Authentication Protocol, (PEAP) defined by Cisco Systems, Microsoft, and RSA Security. PEAP-GTC requires a device identity to be specified and requires that a token value (typically obtained from a physical token device) be specified to prove the authenticity of that device identity. An optional client certificate may also be specified to verify the authenticity of the device identity. In all EAP modes, an optional certificate may be specified to help verify the identity of the authentication server. All

MX: 4.2+

14 PEAP-NONE All

MX: 5.0+

Identity

Used to specify the Identity, which can be a user name, email address, ID number or other unique identifier. The Identity combines with a Password to form an authentication credential for gaining access to a network. Authentication is required only when "Enterprise" is the selected Security Mode. Once a credential is accepted by the Authentication Server, the Identity is replaced by an encryption key and has no further significance.

Specifying an empty (length of zero) value (or the absence of this parm from the XML) will fail to set an Identity.

Shown if: The Network Action is "Add a New Network" and the Authentication is "PEAP-NONE"

Parm Name: Identity

Requires:

  • MX: 4.2+

Anonymous Identity

Used to specify an Anonymous Identity for systems that support separate authentication outside of a secure tunnel.

When using an EAP type that has a secure tunnel over which authentication credentials can be delivered, it is sometimes necessary to specify an Identity outside the protections of the tunnel. In these cases, an Anonymous Identity can be sent so as not to disclose the actual Identity, password or other verifying credentials. A separate Anonymous Identity can be used only if the Authentication Server is set up to support it.

If no Anonymous Identity is specified, then the actual Identity will be sent outside the tunnel, if required. This may still be secure since the password and/or other verifying credentials are always sent inside the tunnel (in modes that use a tunnel for secure credential delivery). Using the actual Identity outside the tunnel would therefore risk disclosure of only part of the information needed to authenticate.

Parm value input rules:

  • String with a minimum of 0 characters and a maximum of 64 characters

Note: Specifying an empty (length of zero) value (or the absence of this parm from the XML) will fail to set an Anonymous Identity.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is NOT "EAP-TLS" or "LEAP"

Parm Name: AnonymousIdentity

Requires:

  • MX: 4.2+

Password

Used to specify a Password to be used to connect to a network. This parameter name will change according to the value of ProtectPassword:

If ProtectPassword is false:

  • Parm name: PasswordClear
  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is NOT "EAP-TLS"

If Protect Password is true:

  • Parm name: PasswordEncrypted
  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is NOT "EAP-TLS"

Parm value input rules:

  • String with a minimum of 0 characters and a maximum of 64 characters

Note: The encryption process for this parameter value is currently undocumented, and the key required to encrypt is unpublished. Since there is currently no way to store an encrypted, server-supplied password within an XML file, mobile device management (MDM) systems cannot use an encrypted password.

Parm Name: PasswordClear, PasswordEncrypted

Requires:

  • MX: 4.2+

Protect Password

Controls whether passwords will be stored as encrypted or clear text while in transit to the device. Passwords specified in Profile Manager are embedded within an XML file and sent to the device for consumption as part of a configuration. Encrypting a Password using this parameter might be desirable as a security measure to prevent extraction and exploitation in case the XML is intercepted while in transit.

Passwords are stored in clear text on the device unless specifically encrypted using the Protect Password Encryption parameter. Encrypted and clear-text Passwords are stored in a protected area on the device that is inaccessible to users and unauthorized applications.

The Password combines with an Identity to form an authentication credential for gaining access to a network. Authentication is required only when "Enterprise" is the selected Security Mode. All authentication types require a Password except EAP-TLS, which uses a client certificate.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is NOT "EAP-TLS"

Parm Name: ProtectPassword

Requires:

  • MX: 4.2+

Password Protect Encryption

Controls whether the Wi-Fi Password stored on the device is encrypted, thereby preventing access to the clear-text Password on the device by any application or malicious exploit.

Note: Enabling this feature prevents the Google Mobile Service (GMS) backup service from successfully restoring Wi-Fi settings to a device, and might effect the operation other device backup systems.

The Password combines with an Identity to form an authentication credential for gaining access to a network. Authentication is required only when "Enterprise" is the selected Security Mode. All authentication types require a Password except EAP-TLS, which uses a client certificate.

Parm Name: PasswordProtectEncryption

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Password Protect Encryption setting; any previously selected setting will be retained. All

MX: 6.1+

1 Enable Causes passwords stored on the device to be encrypted. All

MX: 6.1+

0 Disable Disables encryption for passwords stored on the device. All

MX: 6.1+

Mandatory Server Certificate Name

Used to specify the name of a madatory certificate alias to be used to verify the server.

Parm value input rules:

  • String from 0-64 characters

Notes:

  • When Security Mode is "Enterprise," the device will not need to authenticate to an Authentication Server using the defined Authentication type. This will involve sending potentially sensitive authentication credentials to the Authentication Server. Zebra does not recommended this unless the authenticity of the Authentication Server can be verified, for example, ensuring it is not attempting to carry out a "man in the middle" attack.

  • The device contacts and challenges the Authentication Server to assert and prove its Identity through the use of a server certificate. The device must be able to establish the validity of that certificate and must trust the chain of authority of the issuer of that certificate. This would all occur whether or not a Server Certificate Name is specified.

  • By default, a certificate asserted by an Authentication Server will be trusted if it can be verified to have been issued by any trusted certificate authority. If a Server Certificate Name is supplied, the certificate asserted by an Authentication Server will be trusted only if it is verified to have been issued by that specific trusted certificate authority. This increases the security by preventing the use of certificates issued by authorities that are not trusted to issue certificates to authentication servers.

  • Specifying an empty (length of zero) value (or the absence of this parm from the XML) will fail to set the Optional Server Certificate.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is "EAP-TLS" or "PEAP-MSCHAPV2" or "EAP-TTLS-MSCHAP" or "EAP-FAST-MSCHAPV2" or "EAP-TTLS-PAP" or "PEAP-GTC" or "EAP-FAST-MSCHAPV2" or "EAP-FAST-GTC" or "PEAP-NONE"

Parm Name: OptionalServerCertificate

Requires:

  • MX: 4.2+

Optional Server Certificate Name

Optional parameter that allows the name of a certificate alias to be used to verify the server.

Parm value input rules:

  • String from 0-64 characters

Notes:

  • When Security Mode is "Enterprise," the device will not need to authenticate to an Authentication Server using the defined Authentication type. This will involve sending potentially sensitive authentication credentials to the Authentication Server. Zebra does not recommended this unless the authenticity of the Authentication Server can be verified, for example, ensuring it is not attempting to carry out a "man in the middle" attack.

  • The device contacts and challenges the Authentication Server to assert and prove its Identity through the use of a server certificate. The device must be able to establish the validity of that certificate and must trust the chain of authority of the issuer of that certificate. This would all occur whether or not a Server Certificate Name is specified.

  • By default, a certificate asserted by an Authentication Server will be trusted if it can be verified to have been issued by any trusted certificate authority. If a Server Certificate Name is supplied, the certificate asserted by an Authentication Server will be trusted only if it is verified to have been issued by that specific trusted certificate authority. This increases the security by preventing the use of certificates issued by authorities that are not trusted to issue certificates to authentication servers.

  • Specifying an empty (length of zero) value (or the absence of this parm from the XML) will fail to set the Optional Server Certificate.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is "EAP-TLS" or "PEAP-MSCHAPV2" or "EAP-TTLS-MSCHAP" or "EAP-FAST-MSCHAPV2" or "EAP-TTLS-PAP" or "PEAP-GTC" or "EAP-FAST-MSCHAPV2" or "EAP-FAST-GTC" or "PEAP-NONE"

Parm Name: OptionalServerCertificate

Requires:

  • MX: 4.2+

Optional Client Certificate Name

Optional parameter that allows the name of a client certificate alias to be used to join a network. When Authenticating with EAP types other than EAP-TLS (which would not require a client certificate), a client is still allowed. In this case, the client certificate will be used to authenticate the device to the authentication server as part of the establishment of the secure tunnel over which further authentication credentials will be delivered. The client certificate does not need to be unique, even if the authentication credentials are. The use of a client certificate can introduce an additional level of protection by requiring a device to have a valid client certificate as well as valid authentication credentials. The client certificate serves as a first-pass filter.

Parm value input rules:

  • String with a minimum of 0 characters and a maximum of 64 characters

Note: Specifying an empty (length of zero) value (or the absence of this parm from the XML) will fail to set an Optional Server Certificate.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" the Authentication is "PEAP-MSCHAPV2" or "EAP-TTLS-MSCHAP" or "EAP-TTLS-MSCHAPV2" or "EAP-TTLS-PAP" or "PEAP-GTC" or "EAP-FAST-MSCHAPV2" or "EAP-FAST-GTC" or "PEAP-NONE"

Parm Name: OptionalClientCertificate

Requires:

  • MX: 4.2+

Mandatory Client Certificate Name

Used to specify the name of the certificate alias to be used to join the network (Mandatory). When Authenticating using EAP-TLS, a client certificate is used instead of a Password. When the Authentication type is EAP-TLS, a client certificate must be specified and a Password will not be accepted.

Parm value input rules:

  • String with a minimum of 0 characters and a maximum of 64 characters

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Enterprise" and the Authentication is "EAP-TLS"

Parm Name: MandatoryClientCertificate

Requires:

  • MX: 4.2+

WPA2 Encryption Type

Used to specify the Wi-Fi Protected Access II (WPA2) encryption type to enforce on the network for Wi-Fi log-ins.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal" or "Enterprise" and the WPA Mode is WPA2 or WPA/WPA2

Parm Name: EncryptionWPA2

Option Name Description Device Group Requires
0 Default This value (or the absence of this parm from the XML) will cause no change to the encryption type that is currently selected on the device; any previously selecting setting will be retained. All

MX: 4.2+

1 AES-CCMP Selects use of the Advanced Encryption Standard - Counter mode Cipher block chaining Message authentication code Protocol (AES-CCMP) standard, wherein the AES block cipher is used with a per-packet key length of 128 bits. All

MX: 4.2+

2 TKIP Selects use of the Temporal Key Integrity Protocol (TKIP) standard with a per-packet key length of 128 bits. All

MX: 4.2+

3 AES-CCMP/TKIP Selects the use of either the AES-CCMP standard or the TKIP encryption standard and the proper encryption type to use can be automatically determined by negotiation with the Wi-Fi infrastructure. All

MX: 4.2+

WPA Encryption Type

Used to specify the Wi-Fi Protected Access (WPA) encryption type to enforce on the network for Wi-Fi log-ins. The values that can be selected for Encryption Type will vary based on the selections made for Security Mode and WPA Mode. A selection must always be made for Encryption Type whenever Security Mode is not "Open" (no encryption).

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal" or "Enterprise" and the WPA Mode is WPA

Parm Name: EncryptionWPA

Option Name Description Device Group Requires
0 Default This value (or the absence of this parm from the XML) cause no change to the encryption type that is currently selected on the device; any previously selected setting will be retained. All

MX: 4.2+

1 TKIP Selects use of the Temporal Key Integrity Protocol (TKIP) standard with a per-packet key length of 128 bits. All

MX: 4.2+

WEP Encryption Type

Used to specify the Wired Equialent Privacy (WEP) encryption type to enforce on the network for Wi-Fi log-ins.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal" or "Enterprise" and the WPA Mode is WEP

Parm Name: EncryptionWEP

Option Name Description Device Group Requires
1 WEP-40 Selects use of the Wireless Equivalency Privacy (WEP) standard with a key size of 40 bits. All

MX: 4.2+

2 WEP-104 Selects use of the Wireless Equivalency Privacy (WEP) standard with a key size of 104 bits. All

MX: 4.2+

Key Type

Used to specify the type of encryption key to be used by the network. A key is specified only when the Security Mode is "Personal" since the "Open" Security Mode does not use encryption and the "Enterprise" Security Mode distributes keys automatically after Authentication.

An encryption key can be specified using either of these methods:

  • A hexadecimal value (the key itself)
  • A passphrase used to generate a key using a pre-defined algorithm

The selected method usually depends on the configuration of the Wi-Fi network because the key must be shared between the Wi-Fi infrastructure and the client. Therefore, they must use a common method to specify the key.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal"

Parm Name: KeyType

Option Name Description Device Group Requires
HexKey Hex Key The key used by the network to perform encryption will be specified. All

MX: 4.2+

Passphrase Passphrase A passphrase derived from the specified key and used by the network to perform encryption. All

MX: 4.2+

Protect Key

Enables encryption of the Key. The Key (or the Passphrase used to generate a Key) is generally considered sensitive information since having the Key for a network grants access to that network. Since the Key or Passphrase must be embedded within the XML, it is often desirable to encrypt the Key or Passphrase so it cannot be extracted and exploited if the XML is intercepted. The specified WPA Mode and the Key Type determine what type of Key or Passphrase must used. The value selected for the ProtectKey parameter deterimes whether the Key or Passphrase will be specified as clear or encrypted text.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal"

Parm Name: KeyType

Requires:

  • MX: 4.2+

Passphrase

Controls whether the Key will be encrypted. When the Key Type is Passphrase, then the specified Passphrase will be used to generate the Key. The required Passphrase will vary depending on the WPA Mode specified (WEP or WPA Passphrase).

Note: Currently, the parm value encryption process is not documented and the key that is needed to encrypt is not published. Therefore, an MDM cannot currently use encrypted Keys or Passphrases since there is no way to store an encrypted, server-supplied password in XML file.

If WEP is selected and Protect Key is false:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Passphrase" and the WPA Mode is "WEP" and Protect Key is false
  • Parm name: PassphraseWEPClear
  • Parm value input rules:
    • String with a minimum of 4 characters and a maximum of 32 characters

If WEP is selected and Protect Key is true:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Passphrase" and the WPA Mode is "WEP" and Protect Key is true
  • Parm name: PassphraseWEPEncrypted
  • Parm value input rules:
    • String with a minimum of 4 characters and a maximum of 32 characters
  • Currently, this parm cannot be used effectively by an MDM.

If WEP is not selected and Protect Key is false:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Passphrase" and the WPA Mode is not "WEP" and Protect Key is false
  • Parm name: PassphraseWPAClear
  • Parm value input rules:
    • String with a minimum of 8 characters and a maximum of 63 characters

If WEP is not selected and Protect Key is true:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Passphrase" and the WPA Mode is not "WEP" and Protect Key is true
  • Parm name: PassphraseWPAEncrypted
  • Parm value input rules:
    • String with a minimum of 8 characters and a maximum of 63 characters
  • Currently, this parm cannot be used effectively by an MDM.

Parm Name: PassphraseWEPClear, PassphraseWEPEncrypted, PassphraseWPAClear, PassphraseWPAEncrypted

Requires:

  • MX: 4.2+

Hex Key

When Key Type is Hex Key, then a Key, which is expressed as a sequence of hexadecimal characters, needs to be specified. The type of Key required will vary based on the WPA Mode and Encryption Type specified, since it will need to be either a WEP 40 bit Key, a WEP 104 bit Key, or a 256 bit TKIP/AES-CCMP Key.

Note: Currently, the parm value encryption process is not documented and the key that is needed to encrypt is not published. Therefore, an MDM cannot currently use encrypted Keys or Passphrases since there is no way to store an encrypted, server-supplied password in an XML.

If WEP is not selected and Protect Key is false:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Hex Key" and the WPA Mode is not "WEP" and Protect Key is false
  • Parm name: HexKeyClear
  • Description: Provide the hex key (64 hex chars) used by network
  • Parm value input rules:
    • String with exactly 64 valid hexadecimal characters (e.g. 0-9, A-F) that collectively specify a 256 bit binary key value that can be used for either TKIP or AES-CCMP encryption.

If WEP is not selected and Protect Key is true:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Hex Key" and the WPA Mode is not "WEP" and Protect Key is true
  • Parm name: HexKeyEncrypted
  • Description: Provide the hex key (64 hex chars) used by network
  • Parm value input rules:
    • String with exactly 64 valid hexadecimal characters (e.g. 0-9, A-F) that collectively specify a 256 bit binary key value that can be used for either TKIP or AES-CCMP encryption.
  • Currently, this parm cannot be used effectively by an MDM.

If WEP is selected, the encryption type is WEP-40, and Protect Key is false:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Hex Key" and the WPA Mode is "WEP" and the Encryption Type is "WEP-40" and Protect Key is false
  • Parm name: HexKeyWep40Clear
  • Description: Provide the shared secret WEP-40 key (10 hex chars) used by the network
  • Parm value input rules:
    • String with exactly 10 valid hexadecimal characters (e.g. 0-9, A-F) that collectively specify a 40 bit binary key value that can be used for either WEP encryption.

If WEP is selected, the encryption type is WEP-40, and Protect Key is true:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Hex Key" and the WPA Mode is "WEP" and the Encryption Type is "WEP-40" and Protect Key is true
  • Parm name: HexKeyWep40Encrypted
  • Description: Provide the shared secret WEP-40 key (10 hex chars) used by the network
  • Parm value input rules:
    • String with exactly 10 valid hexadecimal characters (e.g. 0-9, A-F) that collectively specify a 40 bit binary key value that can be used for either WEP encryption.
  • Currently, this parm cannot be used effectively by an MDM.

If WEP is selected, the encryption type is WEP-104, and Protect Key is false:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Hex Key" and the WPA Mode is "WEP" and the Encryption Type is "WEP-104" and Protect Key is false
  • Parm name: HexKeyWep104Clear
  • Description: Provide the shared secret WEP-104 key (26 hex chars) used by the network
  • Parm value input rules:
    • String with exactly 26 valid hexadecimal characters (e.g. 0-9, A-F) that collectively specify a 104 bit binary key value that can be used for either WEP encryption.

If WEP is selected, the encryption type is WEP-104, and Protect Key is true:

  • Settable if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the Key Type is "Hex Key" and the WPA Mode is "WEP" and the Encryption Type is "WEP-104" and Protect Key is true
  • Parm name: HexKeyWep104Encrypted
  • Description: Provide the shared secret WEP-104 key (26 hex chars) used by the network
  • Parm value input rules:
    • String with exactly 26 valid hexadecimal characters (e.g. 0-9, A-F) that collectively specify a 104 bit binary key value that can be used for either WEP encryption.
  • Currently, this parm cannot be used effectively by an MDM.

Parm Name: HexKeyWEPClear, HexKeyWEPEncrypted, HexKeyWPAClear, HexKeyWPAEncrypted

Requires:

  • MX: 4.2+

WEP Key Index

Some Wi-Fi infrastructure that implements a network using WEP encryption may support multiple WEP keys and a WEP index to indicate which key to use at any given time.

Note: Android does not currently support multiple WEP keys per network. Therefore, only the first WEP key (wep[0]) is supported.

Shown if: The Network Action is "Add a New Network" and the Security Mode is "Personal" and the WPA Mode is "WEP"

Parm Name: WepKeyIndex

Option Name Description Device Group Requires
1 wep[0] All

MX: +

2 wep[1] All

MX: +

3 wep[2] All

MX: +

4 wep[3] All

MX: +

Set IP Address

Used to specify a static IP address for the device. Must be an address that is unique to the network on which the device will operate.

Parm value input rules:

  • String containing a valid IPv4 address. For example: "192.168.0.100"

Shown if: The Network Action is "Add a New Network" and "Use DHCP" box is unchecked

Parm Name: IpAddress

Requires:

  • MX: 4.2+

Set Primary Default Gateway

Used to specify the IP address of the default gateway for the device, through which packets to and from outside networks are routed. This parameter is required only if the device must have access to (or from) networks beyond its local subnet.

Parm value input rules:

  • String containing a valid IPv4 address. For example: "192.168.0.1"

Shown if: The Network Action is "Add a New Network" and "Use DHCP" box is unchecked

Parm Name: IpGateway1

Requires:

  • MX: 4.2+

Set Secondary Default Gateway

Used to specify the IP address of an optional second default gateway for the device, through which packets to and from outside networks are routed. This parameter is required only if the device must have access to (or from) networks through a second network adapter.

Parm value input rules:

  • String containing a valid IPv4 address. For example: "192.168.0.1"

Shown if: The Network Action is "Add a New Network" and "Use DHCP" box is unchecked

Parm Name: IpGateway2

Requires:

  • MX: 4.2+

Set Subnet Mask

Used to specify a subnet mask for the device, which defines the network subdivision on which the device will operate.

Parm value input rules:

  • String containing a valid IPv4 address. For example: "255.255.255.0"

Shown if: The Network Action is "Add a New Network" and "Use DHCP" box is unchecked

Parm Name: IpMask

Requires:

  • MX: 4.2+

Set Primary DNS

Used to specify the primary domain name server for the device. This parameter is required only if DNS name resolution is required for the device.

Parm value input rules:

  • String containing a valid IPv4 address. For example: "8.8.8.8"

Shown if: The Network Action is "Add a New Network" and "Use DHCP" box is unchecked

Parm Name: IpDns1

Requires:

  • MX: 4.2+

Set Secondary DNS

Used to specify a secondary domain name server for the device. This parameter is required only if an alternate DNS is required for the device.

Parm value input rules:

  • String containing a valid IPv4 address. For example: "8.8.4.4"

Shown if: The Network Action is "Add a New Network" and "Use DHCP" box is unchecked

Parm Name: IpDns2

Requires:

  • MX: 4.2+

Use Proxy

Controls use of a proxy, an intermediary service that routes HTTP traffic between clients on a device and another network (typically the internet or an intranet). When used, proxy settings can be configured manually can be contained in a PAC file for automatic configuration. When there is a proxy between the Wi-Fi network and some outer network, HTTP-based applications might need to negotiate with the proxy to access the services of the outer network.

In MX 5.0 and higher, the data type for this parameter changed from a boolean (1=true; 0=false) to a value selected from the UseProxy list below.

Parm Name: UseProxy

Option Name Description Device Group Requires
0 None Since MX 5.0 the use of a code over a boolean value was implemented. This value was unaffected. All

MX: 5.0+

1 Manual Since MX 5.0 the use of a code over a boolean was implemented. This value indicates a Manual Proxy. All

MX: 5.0+

3 Proxy Auto-Config Automatically use a proxy. This value was introduced in MX 5.0. All

MX: 5.0+

Proxy Host Name

Provide the Host Name or IP Address of the computer on which the proxy is running. Host Name can be used only if the network provides suitable name resolution. Otherwise, an IP Address would need to be provided.

Since different Wi-Fi networks may have different proxies connecting them to different outer networks, proxy information, if needed, must be configured for each network.

Parm value input rules:

  • String with a minimum of 1 characters and a maximum of 64 characters

Shown if: The Network Action is "Add a New Network" and "Use Proxy" is set to manual.

Parm Name: ProxyHostName

Requires:

  • MX: 4.2+

Bypass Proxy

Used to specify the host name(s) and/or IP address(es) for direct access by a device, bypassing the Proxy server specified in the Proxy Host Name parameter. Multiple names and/or IP addresses can be specified in any combination, separated by commas. Generally used for specifying internal servers and/or as a means to prevent traffic overload on the specified Proxy server. Traffic bound for any host not specifically excluded using this parameter will be routed through the specified Proxy server.

Zebra recommends testing bypass-proxy settings on a working device before general deployment.

Input rules:

  • String from 1-256 characters specifying one or more host names and/or IP addresses separated by commas. For example: "www.MyBypassProxy.com,192.168.1.100, our.internalServer"

Shown if: The Network Action is "Add a New Network" and "Use Proxy" is set to manual.

Parm Name: BypassProxy

Requires:

  • MX: 4.2+

Proxy PAC File URL

Provide the Host Name or IP Address of the location of where the proxy PAC file is located. This can be used only if the network provides suitable name resolution. Otherwise, an IP Address would need to be provided.

Since different Wi-Fi networks may have different proxies connecting them to different outer networks, proxy information, if needed, must be configured for each network.

Parm value input rules:

  • String with a minimum of 1 characters and a maximum of 64 characters

Shown if: The Network Action is "Add a New Network" and "Use Proxy" is set to Proxy Auto-Config.

Parm Name: ProxyPAC

Requires:

  • MX: 5.0+

Proxy Port

Provide the port number of the proxy server on the computer on which the proxy is running on which the proxy is listening.

Shown if: The Network Action is "Add a New Network" and "Use Proxy" is set to manual.

Parm Name: ProxyPort

Requires:

  • MX: 4.2+

Advanced Options

Use of Wi-Fi Advanced Options requires the following:

  • PMKID must be turned on to enable PreAuth (PreAuth =1 and PMKID =1)
  • FT must be turned on to enable FTRIC (FT=1 and FTRIC =1)
  • OKC must be turned off (OKC =0 and PMKID =1) to use PMKID caching

WARNING: Wi-Fi Advanced Options should be used only under the guidance of Zebra Support. Do not use these features unless told to do so by qualified personnel; altering advanced settings can result in undesirable behavior.

Use Advanced Options (checkbox)

Controls Wi-Fi Advanced Options, which whould be used only under the guidance of Zebra Support. Do not use these features unless told to do so by qualified personnel; altering advanced options can result in undesirable device behavior.

Parm Name: UseAdvancedOptions

Option Name Description Device Group Requires
1 (checked) Enables the use of Wi-Fi Advanced Options on the device. All

MX: 4.2+

0 (unchecked) Disables the use of Wi-Fi Advanced Options on the device. All

MX: 4.2+

Auto Time Config

Used to enable/disable AutoTimeConfig feature, a Zebra-specific feature that updates the device timestamp based on Zebra IE in the 802.11 beacon. Not supported on TC70 QC GA1/GA2 running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: AutoTimeConfig

Requires:

  • MX: 4.2+

HFSR

Used to enable/disable Hyper Fast Secure Roam (HFSR), Zebra's fast roam algorithm. Not supported on TC70 QC GA1/GA2, TC75 GA and TC55 GA devices running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: HFSR

Requires:

  • MX: 4.2+

CKM

Used to enable/disable the CCX roam algorithm (CCKM).

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: CCKM

Requires:

  • MX: 4.2+

Aggregated Fast Transition

Controls the Fast Transition roam algorithm (802.11r), which improves on IEEE 802.11r Over-the-DS fast roaming. When used in conjunction with Zebra wireless LAN infrastructure, the device will achieve more reliable and consistent fast roaming. Enabled by default.

Not supported on TC70 QC GA1 devices running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: FT

Requires:

  • MX: 4.2+

FTRIC

Used to enables/disable the Fast Transition Resource Request (802.11r). Not supported on TC70 QC GA1/GA2, TC75 GA or TC55 GA devices running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: FTRIC

Requires:

  • MX: 4.2+

OKC

Used to enable/disable Opportunistic Key Caching (OKC).

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: OKC

Requires:

  • MX: 4.2+

PMKID

Used to enable/disable PMKID Caching. If PMKID is enabled, OKC must be disabled for PMKID caching to operate.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: PMKID

Requires:

  • MX: 4.2+

PreAuth

Used to enable/disable 802.1x Pre-Authentication. Not supported on TC70 QC GA1/GA2 or TC75 GA devices running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: PreAuth

Requires:

  • MX: 4.2+

Power Save Mode

Used to configure the Power Save Mode from the settings table below. The default "Fast Power Save" value must be used for the "Power Save" parameter; the "Do not change" value will result in failure.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: PowerSave

Option Name Description Device Group Requires
0 Do not change All

MX: 4.2+

1 Always Active All

MX: 4.2+

2 Fast Power Save (Deprecated) All

MX: 4.2+

3 Max Power Save (Deprecated) All

MX: 4.2+

4 WMM-PS All

MX: 4.4+

5 Null Data Power Save All

MX: 4.4+

6 PS-POLL All

MX: 4.4+

99 Unsupported All

MX: 6.2+

WLAN Power Save Mode

Used to select the Power Save Mode for the WLAN radio.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: WLANPowerSave

Option Name Description Device Group Requires
0 WMM-PS A

MX: 4.3+

1 Null Data Power Save A

MX: 4.3+

2 PS-POLL A

MX: 4.3+

3 Do not change A

MX: 4.3+

99 Unsupported A

MX: 6.2+

Advanced Logging

Used to start or stop advanced Wi-Fi logging.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: AdvancedLogging

Requires:

  • MX: 4.2+

Enable Restricted Settings UI

Used to enable/disable read-only mode for Wi-Fi settings according to the values in the table below. Not supported on TC70 QC GA1/GA2 running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: EnableRestrictedSettingsUI

Option Name Description Device Group Requires
0 Do not change A

MX: +

1 Disable Restricted WLAN Settings UI A

MX: +

2 Enable Restricted WLAN Settings UI A

MX: +

FIPS

Used to enable/disable FIPS data in motion supported in WLAN. WLAN FIPS 140-2, level 1 compliance. Not supported on TC70 QC GA1/GA2, TC75 GA or TC55 GA devices running Android KitKat.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: FIPS

Requires:

  • MX: 4.2+

Radio Resource Management (802.11k)

Used to enable/disable Radio Resource Management, which measures transmit power, data rates and other wireless characteristics in an effort to optimize communication efficiency. Not supported on TC70 QC GA1/GA2 running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: 802.11K

Requires:

  • MX: 4.3+

Management Frame Protection Mode (802.11w)

Used to specify the Management Frame Protection Mode from the values in the table below. Not supported on TC70 QC GA1/GA2, TC75 GA, or TC55 GA devices running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: 802.11w

Option Name Description Device Group Requires
0 No MFP A

MX: 4.3+

1 Capable A

MX: 4.3+

2 Mandatory A

MX: 4.3+

3 Do not change A

MX: 4.3+

99 Unsupported A

MX: 6.2+

Select Band Preference

Used to specify the preferred Wi-Fi band. Not supported on MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: BandPreference

Option Name Description Device Group Requires
0 No Preference A

MX: 4.3+

1 Prefer 2.4GHz A

MX: 4.3+

2 Prefer 5.0GHz A

MX: 4.3+

3 Do not change A

MX: 4.3+

99 Unsupported A

MX: 6.2+

FT Over The DS

Used to enable/disable Fast Transition over the Distribution System (FTOverTheDS). Enabled by default. Also known as 802.11r Over-the-DS, this fast roam standard reduces the number frames exchanged when the device roams from one AP to another if the infrastructure supports it. Not supported on TC70 QC GA1/GA2, TC75 GA, or TC55 GA devices running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: FTOverTheDS

Requires:

  • MX: 4.3+

AggregatedFT

Used to enable/disable the AggregatedFT feature. Not supported on TC70 QC GA1/GA2, TC75 GA, or TC55 GA devices running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: AggregatedFT

Requires:

  • MX: 4.3+

ScanAssist

Used to enable/disable ScanAssist. This feature improves roaming on Zebra devices by allowing the device to monitor neighboring access points to retrieve roam-related information from the Zebra wireless LAN infrastructure without doing scans. Enabled by default.

Not supported on TC70 QC GA1/GA2, TC75 GA, or TC55 GA devices running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: ScanAssist

Requires:

  • MX: 4.3+

Coverage Hole Detection

Used to enable/disable Coverage Hole Detection, which reports gaps in signal coverage to the Zebra wireless LAN infrastructure. Enabled by default. Network administrators can detect and mitigate coverage gaps present in the network for greater reliability. Not supported on TC70 QC GA1/GA2, TC75 GA, or TC55 GA devices running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: CHD

Requires:

  • MX: 4.3+

Subnet Roam

Used to enable subnet roaming. Not supported on TC70 QC GA1/GA2, TC75 GA, or TC55 GA devices running Android KitKat, or MPA3 RevB-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: SubNetRoam

Requires:

  • MX: 4.4+

WAN Country

Used to enable/disable WAN Country, which obtains country information from the WAN Interface (GSM/CDMA base station) and applies regulatory rules based on the Country Code received. Supported only on WAN based devices. Not supported on TC70 QC GA1/GA2 running Android KitKat, or MPA3 RevB- or RevC-based devices running Android Jelly Bean.

Important: Wi-Fi Advanced Options should be used only at the direction of Zebra Support or other qualified personnel. Altering this setting can result in undesirable behavior.

Shown if: The "Use Advanced Options" box is checked.

Parm Name: WANCountry

Requires:

  • MX: 4.3+

Use Hotspot Options (checkbox)

Determines whether the device can be used as a Wi-Fi hotspot. Hotspot functionality is supported only on Zebra ET50 and ET56 devices running Android 5.0 Lollipop.

Parm Name: UseHotspotOptions

Option Name Description Device Group Requires
0 (unchecked) Prevents the device from being used as a Wi-Fi hotspot. A

MX: 6.3+

1 (checked) Allows the device to be used as a Wi-Fi hotspot. A

MX: 6.3+

Hotspot Enable/Disable

This parameter applies the hotspot configuration on the device. When enabled, the device uses the settings configured with the hotspot parameters below to act as an access point for nearby devices to connect to the internet, sharing the device's Wi-Fi or cellular connection. Hotspot functionality is supported only on certain Zebra devices, including the ET50, ET55 and TC56 devices running Android 5.0 Lollipop and higher.

Note: This parameter does not control activation of the hotspot feature on the device.

Shown if: The "Use Hotspot Options" checkbox is checked

Parm Name: Hotspot

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

1 Enable Enables the device to be used as a Wi-Fi hotspot. A

MX: 6.3+

0 Disable Disables use of the device as a Wi-Fi hotspot. A

MX: 6.3+

Hotspot SSID

Used to specify the Wi-Fi hotspot Service Set Identifier (SSID), the name visible to devices attempting to select the hotspot as an internet access point.

Parm value input rules:

  • String from 1-32 characters containing the desired SSID (case sensitive)

Shown if: The "Specify Hotspot Options" checkbox is checked and "Hotspot" is set to "Enable"

Parm Name: HotspotSSID

Requires:

  • MX: 6.3+

Hotspot RF Band

Used to specify which RF band(s) the device will use for 802.11 communications when configured as a Wi-Fi hotspot. This parameter is usually set automatically through negotiation with the Wi-Fi infrastructure. However, it might sometimes be desirable to limit Wi-Fi communications to certain bands, leaving other bands free for other purposes.

Shown if: The "Specify Hotspot Options" checkbox is checked and "Hotspot" is set to "Enable"

Parm Name: Hotspotband

Option Name Description Device Group Requires
0 2.4GHz Enables the 2.4GHz band for hotspot communications. All

MX: 6.3+

1 5GHz Enables the 5GHz band for hotspot communications. All

MX: 6.3+

Set Hotspot 2.4GHz Channel

Used to set the Wi-Fi communication channel to be used by devices connecting to the device to its Wi-Fi hotspot on the 2.4GHz band.

Shown if: The "Specify Hotspot Options" checkbox is checked and "Hotspot Band" is "2.4GHz"

Parm Name: Hotspot24GHz

Option Name Description Device Group Requires
1 1 Selects channel 1 on the 2.4GHz band A

MX: 6.3+

2 1 Selects channel 2 on the 2.4GHz band A

MX: 6.3+

3 3 Selects channel 3 on the 2.4GHz band A

MX: 6.3+

4 4 Selects channel 4 on the 2.4GHz band A

MX: 6.3+

5 5 Selects channel 5 on the 2.4GHz band A

MX: 6.3+

6 6 Selects channel 6 on the 2.4GHz band A

MX: 6.3+

7 7 Selects channel 7 on the 2.4GHz band A

MX: 6.3+

8 8 Selects channel 8 on the 2.4GHz band A

MX: 6.3+

9 9 Selects channel 9 on the 2.4GHz band A

MX: 6.3+

10 10 Selects channel 10 on the 2.4GHz band A

MX: 6.3+

11 11 Selects channel 11 on the 2.4GHz band A

MX: 6.3+

Set Hotspot 5GHz Channel

Used to set the Wi-Fi communication channel to be used by devices connecting to the device to its Wi-Fi hotspot on the 5GHz band. This band is not supported on Zebra ET50 and ET56 devices.

Shown if: The "Specify Hotspot Options" checkbox is checked and "Hotspot Band" is "5GHz"

Parm Name: Hotspot5GHz

Option Name Description Device Group Requires
36 36 Selects channel 36 on the 5GHz band A

MX: 6.3+

40 40 Selects channel 40 on the 5GHz band A

MX: 6.3+

44 44 Selects channel 44 on the 5GHz band A

MX: 6.3+

48 48 Selects channel 48 on the 5GHz band A

MX: 6.3+

52 52 Selects channel 52 on the 5GHz band A

MX: 6.3+

60 60 Selects channel 60 on the 5GHz band A

MX: 6.3+

64 64 Selects channel 64 on the 5GHz band A

MX: 6.3+

100 100 Selects channel 100 on the 5GHz band A

MX: 6.3+

104 104 Selects channel 104 on the 5GHz band A

MX: 6.3+

108 108 Selects channel 108 on the 5GHz band A

MX: 6.3+

112 112 Selects channel 112 on the 5GHz band A

MX: 6.3+

116 116 Selects channel 116 on the 5GHz band A

MX: 6.3+

120 120 Selects channel 120 on the 5GHz band A

MX: 6.3+

124 124 Selects channel 124 on the 5GHz band A

MX: 6.3+

128 128 Selects channel 128 on the 5GHz band A

MX: 6.3+

132 132 Selects channel 132 on the 5GHz band A

MX: 6.3+

136 136 Selects channel 136 on the 5GHz band A

MX: 6.3+

140 140 Selects channel 140 on the 5GHz band A

MX: 6.3+

149 149 Selects channel 149 on the 5GHz band A

MX: 6.3+

153 153 Selects channel 153 on the 5GHz band A

MX: 6.3+

157 157 Selects channel 157 on the 5GHz band A

MX: 6.3+

161 161 Selects channel 161 on the 5GHz band A

MX: 6.3+

165 165 Selects channel 165 on the 5GHz band A

MX: 6.3+

Hotspot Security Mode

Controls whether user credentials will be required on a device before allowing it to connect to the Wi-Fi hotspot.

Shown if: The "Specify Hotspot Options" checkbox is checked and "Hotspot" is set to "Enable"

Parm Name: HotspotSecurityMode

Option Name Description Device Group Requires
0 Open Allows any device to connect to the Wi-Fi hotspot without entering credentials. A

MX: 6.3+

1 WPA2/PSK Requires user credentials to be entered before allowing a connection to the Wi-Fi hotspot. A

MX: 6.3+

Hotspot Passphrase Clear

Used to provide a password for accessing the hotspot and to store it as clear text.

Parm value input rules:

  • String from 1-32 characters containing the hotspot password

Shown if: The "Specify Hotspot Options" is checked, the "Protect Hotspot Passphrase" checkbox is unchecked and "Hotspot" is set to "Enable"

Parm Name: HotspotPassphraseClear

Requires:

  • MX: 6.3+

Protect Hotspot Passphrases (checkbox)

Determines whether the hotspot password stored on the device is encrypted, thereby preventing access to the password by an application or malicious exploit.

Shown if: Hotspot is set to "Enable" and Hotspot Security mode is not "Open"

Parm Name: ProtectHotspotPassphrases

Option Name Description Device Group Requires
0 (unchecked) Stores hotspot passwords as clear text A

MX: 6.3+

1 (checked) Stores hotspot password as encrypted text A

MX: 6.3+

Hotspot Passphrase Encrypted

Used to provide a password for accessing the hotspot and to store it in encrypted form.

Parm value input rules:

  • String from 1-32 characters containing the hotspot password

Shown if: The "Specify Hotspot Options" and "Protect Hotspot Passphrase" checkboxes are checked, "Hotspot" is set to "Enable" and "Hotspot Security Mode" is "WPA2/PSK"

Parm Name: HotspotPassphraseEncrypted

Requires:

  • MX: 6.3+

Use OmniTrail Options (checkbox)

Determines whether OmniTrail device location services are used and their options configurable.

Parm Name: UseOmniTrailOptions

Option Name Description Device Group Requires
0 (unchecked) Disables OmniTrail device location services and options. A

MX: 6.3+

1 (checked) Enables OmniTrail device location services and options. A

MX: 6.3+

OmniTrail Enable/Disable

This is the On/Off switch for OmniTrail location services and options on the device.

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailEnable

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

1 Enable Enables OmniTrail device location services and options. A

MX: 6.3+

0 Disable Disables OmniTrail device location services and options. A

MX: 6.3+

OmniTrail Data-Rate Option

Controls the Wi-Fi operating mode to be used by OmniTrail device location services.

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailDataRateOption

Option Name Description Device Group Requires
0 abg Sets Wi-Fi for 802.11abg mode. A

MX: 6.3+

1 11n Sets Wi-Fi for 802.11n mode. A

MX: 6.3+

2 11ac Sets Wi-Fi for 802.11ac mode. A

MX: 6.3+

3 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

OmniTrail "abg" Data Rates

Sets the data rate used when OmniTrail device location services operate in 802.11abg mode.

Shown if: The "Specify OmniTrail Options" checkbox is checked and "OmniTrail DataRate Options" is set to "abg"

Parm Name: datarate_abg

Option Name Description Device Group Requires
0 1 Sets the data rate to 1 Mbps A

MX: 6.3+

1 2 Sets the data rate to 2 Mbps A

MX: 6.3+

2 5.5 Sets the data rate to 5.5 Mbps A

MX: 6.3+

3 6 Sets the data rate to 6 Mbps A

MX: 6.3+

4 9 Sets the data rate to 9 Mbps A

MX: 6.3+

5 11 Sets the data rate to 11 Mbps A

MX: 6.3+

6 12 Sets the data rate to 12 Mbps A

MX: 6.3+

7 18 Sets the data rate to 18 Mbps A

MX: 6.3+

8 24 Sets the data rate to 24 Mbps A

MX: 6.3+

9 36 Sets the data rate to 36 Mbps A

MX: 6.3+

10 48 Sets the data rate to 48 Mbps A

MX: 6.3+

11 54 Sets the data rate to 54 Mbps A

MX: 6.3+

OmniTrail "11ac" Data Rates

Sets the data rate used when OmniTrail device location services operate in 802.11ac mode.

Shown if: The "Specify OmniTrail Options" checkbox is checked and "OmniTrail DataRate Options" is set to "11ac"

Parm Name: datarate_11ac

Option Name Description Device Group Requires
28 MCS0_1 Sets the data rate to 29.3 Mbps A

MX: 6.3+

29 MCS1_1 Sets the data rate to 58.5 Mbps A

MX: 6.3+

30 MCS2_1 Sets the data rate to 87.8 Mbps A

MX: 6.3+

31 MCS3_1 Sets the data rate to 117 Mbps A

MX: 6.3+

32 MCS4_1 Sets the data rate to 175.5 Mbps A

MX: 6.3+

33 MCS5_1 Sets the data rate to 234 Mbps A

MX: 6.3+

34 MCS6_1 Sets the data rate to 263.3 Mbps A

MX: 6.3+

35 MCS7_1 Sets the data rate to 292.5 Mbps A

MX: 6.3+

36 MCS8_1 Sets the data rate to 351 Mbps A

MX: 6.3+

37 MCS9_1 Sets the data rate to 390 Mbps A

MX: 6.3+

38 MCS0_2 Sets the data rate to 58.5 Mbps A

MX: 6.3+

39 MCS1_2 Sets the data rate to 117 Mbps A

MX: 6.3+

40 MCS2_2 Sets the data rate to 175.5 Mbps A

MX: 6.3+

41 MCS3_2 Sets the data rate to 234 Mbps A

MX: 6.3+

42 MCS4_2 Sets the data rate to 351 Mbps A

MX: 6.3+

43 MCS5_2 Sets the data rate to 468 Mbps A

MX: 6.3+

44 MCS6_2 Sets the data rate to 526.5 Mbps A

MX: 6.3+

45 MCS7_2 Sets the data rate to 585 Mbps A

MX: 6.3+

46 MCS8_2 Sets the data rate to 702 Mbps A

MX: 6.3+

47 MCS9_2 Sets the data rate to 780 Mbps A

MX: 6.3+

OmniTrail "11n" Data Rates

Sets the data rate used when OmniTrail device location services operate in 802.11n mode.

Shown if: The "Specify OmniTrail Options" checkbox is checked and "OmniTrail DataRate Options" is set to "11n"

Parm Name: datarate_11n

Option Name Description Device Group Requires
12 MCS0 Sets the data rate to 6.5 Mbps A

MX: 6.3+

13 MCS1 Sets the data rate to 13 Mbps A

MX: 6.3+

14 MCS2 Sets the data rate to 19.5 Mbps A

MX: 6.3+

15 MCS3 Sets the data rate to 26 Mbps A

MX: 6.3+

16 MCS4 Sets the data rate 39 Mbps A

MX: 6.3+

17 MCS5 Sets the data rate to 52 Mbps A

MX: 6.3+

18 MCS6 Sets the data rate 58.5 Mbps A

MX: 6.3+

19 MCS7 Sets the data rate 65 Mbps A

MX: 6.3+

20 MCS8 Sets the data rate 13 Mbps A

MX: 6.3+

21 MCS9 Sets the data rate to 26 Mbps A

MX: 6.3+

22 MCS10 Sets the data rate to 39 Mbps A

MX: 6.3+

23 MCS11 Sets the data rate to 52 Mbps A

MX: 6.3+

24 MCS12 Sets the data rate to 78 Mbps A

MX: 6.3+

25 MCS13 Sets the data rate to 104 Mbps A

MX: 6.3+

26 MCS14 Sets the data rate to 117 Mbps A

MX: 6.3+

27 MCS15 Sets the data rate to 130 Mbps A

MX: 6.3+

OmniTrail Type

Specifies the type of OmniTrail services to be used according to the access points in use at the facility.

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailType

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

1 Enable Enables OmniTrail services for Extreme Networks APs. A

MX: 6.3+

0 Disable Enables OmniTrail services for Cisco APs. A

MX: 6.3+

OmniTrail Subtype

Used to select the OmniTrail Subtype, which can help differentiate between regular and special OmniTrail beacons on the Cisco or Extreme Networks access point selected in OmniTrailType parameter.

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailSubtype

Option Name Description Device Group Requires
16 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

0 0 Sets the OmniTrail Subtype to 0. A

MX: 6.3+

1 1 Sets the OmniTrail Subtype to 1. A

MX: 6.3+

2 1 Sets the OmniTrail Subtype to 2. A

MX: 6.3+

3 3 Sets the OmniTrail Subtype to 3. A

MX: 6.3+

4 4 Sets the OmniTrail Subtype to 4. A

MX: 6.3+

5 5 Sets the OmniTrail Subtype to 5. A

MX: 6.3+

6 6 Sets the OmniTrail Subtype to 6. A

MX: 6.3+

7 7 Sets the OmniTrail Subtype to 7. A

MX: 6.3+

8 8 Sets the OmniTrail Subtype to 8. A

MX: 6.3+

9 9 Sets the OmniTrail Subtype to 9. A

MX: 6.3+

10 10 Sets the OmniTrail Subtype to 10. A

MX: 6.3+

11 11 Sets the OmniTrail Subtype to 11. A

MX: 6.3+

12 12 Sets the OmniTrail Subtype to 12. A

MX: 6.3+

13 13 Sets the OmniTrail Subtype to 13. A

MX: 6.3+

14 14 Sets the OmniTrail Subtype to 14. A

MX: 6.3+

15 15 Sets the OmniTrail Subtype to 15. A

MX: 6.3+

OmniTrail Priority

Used to assign a Priority level from 0-3 (lowest to highest) for the OmniTrail beacon frame on Extreme Networks access points.

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailPriority

Option Name Description Device Group Requires
4 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

0 0 Sets the OmniTrail Priority to 0 (lowest). A

MX: 6.3+

1 1 Sets the OmniTrail Priority to 1. A

MX: 6.3+

2 2 Sets the OmniTrail Priority to 2. A

MX: 6.3+

3 3 Sets the OmniTrail Priority to 3 (highest). A

MX: 6.3+

OmniTrail Channel

Used to specify as many as four (4) OmniTrail Channels from the 2.4GHz and/or 5GHz bands to which to apply OmniTrail device-location services.

Parm value input rules:

  • String containing a comma-separated list of 1-4 channels from 2.4GHz and/or 5GHz bands

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailChannel

Requires:

  • MX: 6.3+

Examples

Managing Certificates Related to Wi-Fi Networks

Initialize the Android KeyStore

Note: Must be done for any new device before installing certificates.

Without a password:


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="4"/>
    </characteristic>
</wap-provisioningdoc>


With a password:


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="4"/>
        <characteristic type="keystore-details">
            <parm name="KeystorePassword" value="password"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Remove a Certificate:


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="2"/>
        <characteristic type="cert-details">
            <parm name="CertAlias" value="certName1"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Install a CA certificate (.PEM file):


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="1"/>
        <characteristic type="cert-details">
            <parm name="CertAlias" value="certName2"/>
            <parm name="CertType" value="5"/>
            <parm name="CertMethod" value="2"/>
            <parm name="CertFileCA" value="/path/to/cert.pem"/>
            <parm name="CertAdjustClock" value="false"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Install a client certificate (.PEM file):


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="1"/>
        <characteristic type="cert-details">
            <parm name="CertAlias" value="certName2"/>
            <parm name="CertType" value="6"/>
            <parm name="CertMethod" value="2"/>
            <parm name="CertFileClient" value="/path/to/cert.pem"/>
            <parm name="CertAdjustClock" value="false"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Install a client certificate and private key (.PFX file):


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="1"/>
        <characteristic type="cert-details">
            <parm name="CertAlias" value="certName2"/>
            <parm name="CertType" value="8"/>
            <parm name="CertMethod" value="2"/>
            <parm name="CertFileClient" value="/path/to/cert.pem"/>
            <parm name="CertAdjustClock" value="false"/>
            <parm name="PrivateKeyPassword" value="pass"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Install a client certificate and private key (.P12 file):


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="1"/>
        <characteristic type="cert-details">
            <parm name="CertAlias" value="certName2"/>
            <parm name="CertType" value="9"/>
            <parm name="CertMethod" value="2"/>
            <parm name="CertFileClient" value="/path/to/cert.pem"/>
            <parm name="CertAdjustClock" value="false"/>
            <parm name="PrivateKeyPassword" value="pass"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Install a client certificate and private key (.PKCS12 file):


<wap-provisioningdoc>
    <characteristic type="CertMgr" version="4.2" >
        <parm name="CertAction" value="1"/>
        <characteristic type="cert-details">
            <parm name="CertAlias" value="certName2"/>
            <parm name="CertType" value="9"/>
            <parm name="CertMethod" value="10"/>
            <parm name="CertFileClient" value="/path/to/cert.pem"/>
            <parm name="CertAdjustClock" value="false"/>
            <parm name="PrivateKeyPassword" value="pass"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Country Selection

Selecting a Country:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="1"/>
        <characteristic type="Regulatory">
            <parm name="Country" value="US"/>
        </characteristic>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
    </characteristic>
</wap-provisioningdoc>


Using the Auto Option:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="1"/>
        <characteristic type="Regulatory">
            <parm name="Country" value="AUTO"/>
        </characteristic>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
    </characteristic>
</wap-provisioningdoc>


Band Selection

Set 2.4GHz:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <characteristic type="Radio">
            <parm name="BandSelection" value="2.4GHz"/>
            <characteristic type="ChannelSelection">
                <parm name="2.4GHzChannels" value="1"/>
            </characteristic>
        </characteristic>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
    </characteristic>
</wap-provisioningdoc>


Set 5.0GHz:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <characteristic type="Radio">
            <parm name="BandSelection" value="5.0GHz"/>
            <characteristic type="ChannelSelection">
                <parm name="5.0GHzChannels" value="36"/>
            </characteristic>
        </characteristic>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
    </characteristic>
</wap-provisioningdoc>


Set Auto (both 2.4 and 5.0GHz):


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <characteristic type="Radio">
            <parm name="BandSelection" value="Auto"/>
            <characteristic type="ChannelSelection">
                <parm name="2.4GHzChannels" value="1"/>
                <parm name="5.0GHzChannels" value="36"/>
            </characteristic>
        </characteristic>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
    </characteristic>
</wap-provisioningdoc>


Add Wi-Fi Network

Adding an Open Network:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="0"/>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding a Personal Network with WPA:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="1"/>
            <parm name="WPAMode" value="1"/>
            <characteristic type="key-details">
                <parm name="KeyType" value="Passphrase"/>
                <parm name="ProtectKey" value="0"/>
                <parm name="PassphraseWPAClear" value="KsdU6X3u"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding a Personal Network with WPA and TKIP:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="1"/>
            <parm name="WPAMode" value="1"/>
            <characteristic type="auth-details">
                <characteristic type="encryption-details">
                    <parm name="EncryptionWPA" value="1"/>
                </characteristic>
            </characteristic>
            <characteristic type="key-details">
                <parm name="KeyType" value="Passphrase"/>
                <parm name="ProtectKey" value="0"/>
                <parm name="PassphraseWPAClear" value="KsdU6X3u"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding a Personal Network with WPA2:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="1"/>
            <parm name="WPAMode" value="2"/>
            <characteristic type="key-details">
                <parm name="KeyType" value="Passphrase"/>
                <parm name="ProtectKey" value="0"/>
                <parm name="PassphraseWPAClear" value="KsdU6X3u"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding a Personal Network with WPA/WPA2:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="1"/>
            <parm name="WPAMode" value="3"/>
            <characteristic type="key-details">
                <parm name="KeyType" value="Passphrase"/>
                <parm name="ProtectKey" value="0"/>
                <parm name="PassphraseWPAClear" value="KsdU6X3u"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding a Personal Network with WEP:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="1"/>
            <parm name="WPAMode" value="4"/>
            <characteristic type="auth-details">
                <characteristic type="encryption-details">
                    <parm name="EncryptionWEP" value="1"/>
                </characteristic>
            </characteristic>
            <characteristic type="key-details">
                <parm name="KeyType" value="Passphrase"/>
                <parm name="ProtectKey" value="0"/>
                <parm name="PassphraseWEPClear" value="KsdU6X3u"/>
                <parm name="WepKeyIndex" value="1"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding an Enterprise Network with WPA:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="2"/>
            <parm name="WPAMode" value="1"/>
            <parm name="Authentication" value="1"/>
            <characteristic type="auth-details">
                <parm name="OptionalServerCertificate" value="serverCertName"/>
                <parm name="MandatoryClientCertificate" value="clientCertName"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding an Enterprise Network with WPA2:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="2"/>
            <parm name="WPAMode" value="2"/>
            <parm name="Authentication" value="1"/>
            <characteristic type="auth-details">
                <parm name="OptionalServerCertificate" value="serverCertName"/>
                <parm name="MandatoryClientCertificate" value="clientCertName"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding an Enterprise Network with WPA/WPA2:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="2"/>
            <parm name="WPAMode" value="3"/>
            <parm name="Authentication" value="1"/>
            <characteristic type="auth-details">
                <parm name="OptionalServerCertificate" value="serverCertName"/>
                <parm name="MandatoryClientCertificate" value="clientCertName"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>


Adding an Enterprise Network with WEP:


<wap-provisioningdoc>
    <characteristic type="Wi-Fi" version="4.4" >
        <parm name="UseRegulatory" value="0"/>
        <parm name="UseDiagnosticOptions" value="0"/>
        <parm name="UseAdvancedOptions" value="0"/>
        <parm name="NetworkAction" value="Add"/>
        <characteristic type="network-profile">
            <parm name="SSID" value="Zebra"/>
            <parm name="SecurityMode" value="2"/>
            <parm name="WPAMode" value="4"/>
            <parm name="Authentication" value="1"/>
            <characteristic type="auth-details">
                <characteristic type="encryption-details">
                    <parm name="EncryptionWEP" value="1"/>
                </characteristic>
                <parm name="OptionalServerCertificate" value="serverCertName"/>
                <parm name="MandatoryClientCertificate" value="clientCertName"/>
            </characteristic>
            <parm name="UseDHCP" value="1"/>
            <parm name="UseProxy" value="0"/>
        </characteristic>
    </characteristic>
</wap-provisioningdoc>

OmniTrail Flag

Used to set a Flag for the OmniTrail beacon frame on Extreme Networks access points.

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailFlag

Option Name Description Device Group Requires
4 Do not change This value (or the absence of this parm from the XML) will cause no change to the current Wi-Fi setting; any previously selected setting will be retained. A

MX: 6.3+

3 3 Sets the OmniTrail flag to 3. A

MX: 6.3+

2 2 Sets the OmniTrail flag to 2. A

MX: 6.3+

1 1 Sets the OmniTrail flag to 1. A

MX: 6.3+

0 0 Sets the OmniTrail flag to 0. A

MX: 6.3+

OmniTrail Interval

Used to specify the interval (in ms) at which to emit a locational beacon. More frequent beacon emmissions are generally more effective at determining location of devices that are indoors or within other tightly bounded spaces.

Parm value input rules:

  • Integer from 200-5000 (ms) containing the desired interval at which to emit a locational beacon

Shown if: The "Specify OmniTrail Options" checkbox is checked

Parm Name: OmniTrailInterval

Requires:

  • MX: 6.3+

Captive Portal Detection

This is the On/Off switch for the detection of a Captive Portal, which requires user interaction to activate an open Wi-Fi connection. Captive portals are often used on public-access networks such as those at airports, hotels and coffee shops.

Parm Name: CaptivePortalDetection

Option Name Description Device Group Requires
2 Do not change This value (or the absence of this parm from the XML) will cause no change to the setting; any previously selected setting will be retained. A

MX: 6.3+

1 Enable Enables the detection of a captive portal. A

MX: 6.3+

0 Disable Disables the detection of a captive portal. A

MX: 6.3+